Top seller
No results were found for the filter!
MUX click The MUX509 itself uses three control pins to perform signal switching. These pins are routed to the mikroBUS™, allowing simple interfacing with the host MCU. In addition, MUX click comes equipped with the three-pole terminal for the...
₹ 1,789.00 *
PWR Meter click The measurement circuitry is completely isolated from the mikroBUS™, thus preventing any power surges from the measured circuit, which might cause damage to the low voltage components. Featuring very accurate power monitoring IC, with...
₹ 4,409.00 *
PWR Meter 2 click The Click board™ comes with two screw terminals, allowing the external circuit to be easily connected. Besides measuring the properties of an externally connected circuit, PWR Meter 2 click can be used to measure the power consumption of...
₹ 1,999.00 *
V to Hz 2 click This device is well suited to be used in a number of various voltage to frequency applications: it can be used in instrumentation applications, industrial, and automation markets. It is well suited for use in AD conversion, long-term...
₹ 4,409.00 *
Hz to V 2 click These features allow HZ to V 2 click to be used in various frequency to voltage applications: in instrumentation, industrial, and automation markets. It is well suited for use in A/D conversion, long-term integration, frequency to...
₹ 4,409.00 *
Multimeter click Since there are four distinctive properties that can be measured with Multimeter click which all require different measuring techniques, several different ICs had to be used on the Click board™. Starting with the high-quality, low noise...
₹ 4,099.00 *
ADC 7 click A high dynamic range of this click allows it to be used for very precise sampling of the input voltage between A+ and A-, as it allows detection of changes down to a magnitude of few nanovolts. ADC 7 click accepts a differential voltage...
₹ 10,399.00 *
Slider 2 Click The output from the potentiometer is buffered by the high-performance rail-to-rail operational amplifier, which ensures clean and low-noise signal to the VO pin of the Click Board. Featuring a very accurate voltage reference and a...
₹ 2,099.00 *
Current 2 Click Current 2 click features a very low error margin of less than 0.2%, a very low offset and quiescent current, allowing the voltage across the sense resistor as high as 2.5V. The output current is converted to voltage and fed to the 10-bit...
₹ 1,789.00 *
DigiVref Click A precisely controlled voltage reference is often required in various designs. It is most commonly available in a form of an integrated circuit. However, voltage reference ICs have a number of disadvantages: they are usually designed to...
₹ 1,579.00 *
POT 2 Click Having the ability to adjust the voltage on the AN pin very accurately, this Click board™ can be used for development of applications that require voltage reference other than what is commonly available as an output from a dedicated IC....
₹ 1,259.00 *
RMS to DC click Featuring a very high linearity, a rail-to-rail common mode voltage, a true RMS-to-DC conversion with a minimum number of external components required, an excellent linearity that allows direct application with no compensation elements...
₹ 3,679.00 *
3G-AA Click BroadR-Reach NANO GPS click RS232 click IR Sense 2 RS485 4 Click DALI Click Balancer 3 RS232 SPI click Tamper 2 click UART 1-Wire Angle 4 click GSR click Mikromedia 4 Pi 4 Click 4G LTE-APJ TMR Angle Click PS 2 click OBDII click 6DOF IMU click M-Bus Master DHT22 2 click Manometer 2 BarGraph 3 RiBUS Click Slider click Hall current 2 LTE IoT 2 Click iButton click 4X4 RGB click Accel 12 click 6LoWPAN T click Waveform Click USB I2C click I2C to SPi GPS Click LED Driver 3 IrDA 3 click MCP2517FD click Vibro Motor Hall Current 4 Heart Rate 7 DC MOTOR 3 Pedometer 3 6LoWPAN C click 13DOF Click
Viewed