Top seller
No results were found for the filter!
GSM3 click With GSM3 click you can have two of the most used wireless communication protocols in one device — GSM/GPRS and Bluetooth. The click has an onboard 2.4 GHz active antenna, so it is Bluetooth compatible. It carries the SIM800H quad-band...
₹ 5,989.00 *
BLE2 click BLE2 click is an excellent choice if you want simple, temporary connectivity with your smart devices over Bluetooth 4.1. BLE2 click features the RN4020 module from Microchip, that integrates RF, a baseband controller, and a command API...
₹ 3,149.00 *
WiFi2 click WiFi2 click features the HLK-M30 WiFi module with a built-in TCP/IP protocol stack. The click is designed to run on a 3.3V power supply; it communicates with the target MCU over an UART interface and the following mikroBUS™ pins: AN,...
₹ 3,049.00 *
NFC Tag click NFC Tag click carries an M24SR64 NFC/RFID tag IC with a dual interface and 8KB of high-reliability EEPROM built-in. The RF protocol is compatible with both NFC Forum Type 4 Tag and ISO/IEC 14443 Type A. There’s three ways to operate NFC...
₹ 1,259.00 *
ccRF2 click ccRF2 click carries CC1120 , the fully integrated, high-performance single-chip radio transceiver with extremely low power consumption. Designed mainly for the ISM (Industrial, Scientific, and Medical) and SRD (Short Range Device)...
₹ 3,779.00 *
GPS3 click GPS3 click carries Quectel’s L80 GPS module, a high-sensitivity ultra slim GPS module with a patch antenna. The module incorporates several technologies that enhance the GPS performance. EASY™ Technology ensures that L80 can calculate...
₹ 4,619.00 *
BLE P click BLE P click carries the nRF8001 IC that allows you to add Bluetooth 4.0 to your device. The click communicates with the target board MCU through mikroBUS™ SPI (CS, SCK, MISO, MOSI), RDY and ACT lines, and runs on 3.3V power supply....
₹ 2,629.00 *
tRF click tRF click is an add-on board in mikroBUS form factor. It can be used to wirelessly send and receive UART data. It features the Telit LE70-868 - 868 MHz transceiver module with an embedded stack that is easy to integrate and use in...
₹ 6,199.00 *
ccRF click ccRF click is a low-power 2.4 GHz transceiver designed for the 2400- 2483.5 MHz ISM and SRD frequency bands. It features CC2500 Low-Power 2.4 GHz RF transceiver as well as PCB trace antenna. The CC2500 is integrated with a highly...
₹ 2,309.00 *
RFid click RFid click features CR95HF 13.56 MHz contactless transceiver as well as trace antenna. The click is designed to run on a 3.3V power supply only. It communicates with the target MCU via mikroBUS™ UART (TX, RX), SPI (MISO, MOSI, SCK, CS)...
₹ 3,049.00 *
IR click IR Click is an add-on board in mikroBUS form factor. It’s a compact and easy solution for adding infrared (IR) remote control module to your design. It features TSOP38338 IR receiver module as well as QEE113 IR emitting diode. The 38 kHz...
₹ 999.00 *
GSM2 click GSM2 click is the simplest way to add GSM/GPRS communication layer to your project, for fast transmission of data, voice, and SMS. It features the Quectel quad-band M95 FA GSM/GPRS module that has an integrated TCP/IP protocol stack,...
₹ 4,619.00 *
1-Wire I2C ATA663254 click CAN SPI click USB I2C click Light Temp Button Y Click DALI 2 click RS485 click 5V AC Current NFC click V to Hz 2 click RS485 4 Click MCP2517FD click Voltmeter click Accel 7 click DHT22 2 click PWM 2 click RS485 2 click I2C Isolator 2 BroadR-Reach CAN Isolator Heart rate 6 ATA6570 click Brushless 2 BarGraph 2 iButton click IR Beacon Click USB UART 2 I2C Isolator DALI Click Brushless 3 RS232 2 click UPS click 4-20 mA R click GSM Click RS485 click RS232 click RS232 Isolator MCP25625 click UART I2C SPI PWM click EERAM 3.3V LLC-I2C Click LLC SPI Click ETH Click WiFi 5 click
Viewed