THERMO 2 click

Please inform me as soon as the product is available again.
₹ 1,579.00 *

Prices incl. GST

Out of Stock.

  • MIKROE-1840
  • MIKROE-1840
THERMO 2 click  carries  DS1825 , a programmable resolution digital thermometer IC...more
Product information "THERMO 2 click"

THERMO 2 click carries DS1825, a programmable resolution digital thermometer IC with a unique 64-bit address. The click is designed to run on a 3.3V power supply. The board communicates with the target microcontroller through a 1-wire interface. Using the onboard jumper you can select between two outputs: GP1 (default mikroBUS™ AN pin), and GPO (default PWM pin).

Temperature range

The sensor aboard THERMO 2 click measures temperature within a range from –10°C to 85°C with ±0.5°C accuracy.

DS1825 digital thermometer

You can specify the resolution of the measurements, from 9 to 12-bit, depending on the application. Because each DS1825 has a unique 64-bit serial code, many of them can function on the same 1-wire bus.

The 4-bit location address lets you set up a unique ID for up to 16 sensors that operate on a single 1-Wire bus.

Onboard jumpers

The board features a set of four onboard jumpers (zero ohm resistors) for specifying a unique address for the sensor.

A separate jumper lets you select the sensor’s output between GP1 and GP0 pins.

THERMO 2 click also features four Address Select jumpers for setting a unique ID for the sensor (allowing for up to 16 sensors to operate on a single 1-Wire bus).

Key features

  • DS1825 digital thermometer
    • ±0.5°C accuracy from -10°C to +85°C  
    • Thermometer Resolution is User-Selectable from 9 to 12 Bits
    • Alarm function (user-programmable)
  • Interface: AN, PWM
  • 3.3V power supply

Specification

Type Temperature,Humidity
Applications HVAC systems, weather stations… especially suitable for connecting multiple sensors to a single MCU
On-board modules DS1825 digital thermometer IC
Key Features 1-Wire interface. Sensitivity: -10°C to 85°C with ±0.5°C accuracy. User selectable 9 to 12-bit measurement resolution
Key Benefits Four onboard jumpers for specifying sensor ID
Interface GPIO
Input Voltage 3.3V
Compatibility mikroBUS
Click board size S (28.6 x 25.4 mm)

Pinout diagram

This table shows how the pinout on THERMO click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

NotesPinMikrobus logo.png

mikroBUStm

PinNotes
Data Input/Output pin GPIO1 1 AN PWM 16 GPIO0 Data Input/Output pin
Not connected NC 2 RST INT 15 NC Not connected
Not connected NC 3 CS TX 14 NC Not connected
Not connected NC 4 SCK RX 13 NC Not connected
Not connected NC 5 MISO SCL 12 NC Not connected
Not connected NC 6 MOSI SDA 11 NC Not connected
Power supply +3.3V 7 3.3V 5V 10 NC Not connected
Ground GND 8 GND GND 9 GND Ground

Programming

Code examples for THERMO 2 click, written for MikroElektronika hardware and compilers are available on Libstock.

This code snippet initializes the display and the digital thermometer, and starts the conversion in an enless loop, reads the scratch pad and displays the temperature.

01 void main() {
02   Display_Init();
03   DS1825_Init(12);
04   delay_ms(100);
05   while(1) {
06     DS1825_StartConversion();
07     DS1825_ReadScratchPad();
08     Display_Temperature();
09     delay_ms(500);
10   }
11 }

 

Related links to "THERMO 2 click"
Read, write and discuss reviews...more
Customer evaluation for "THERMO 2 click"
Write a review
Reviews will be activated after verification.

The fields marked with * are required.

Viewed