Top seller
No results were found for the filter!
Wio Lite MG126 - ATSAMD21 Cortex-M0 Blue... Last week, we released the first product of the Wio Lite series , the Wio Lite W600 , which is a SAM D21 + W600 WiFi development board and it was well received by users. Today, we bring you another new product in the Wio Lite series, the...
₹ 1,099.00 *
Wio Lite W600 - ATSAMD21 Cortex-M0 Wireless... Well, you can find hundreds of WiFi shields, modules for Arduino out there. However, most of them are either unstable, either oversized or expensive. When the Arduino and wifi chips are integrated on one development board, it is another...
₹ 1,099.00 *
12V DC Motor 350RPM w/Encoder (12kg*cm) This is a gear motor with encoder. It is a motor with a 34:1 gearbox and an integrated quadrature encoder that provides a resolution of 11 pulse single per round giving a maximum output of 374 within one round. With an Arduino controller...
₹ 2,869.00 *
MXP Extender Cable for myRIO This cable is designed to extend reach of the myRIO expansion port (MXP). The MXP extender cable is perfectly suited for mounting expansion boards, such as the Pmod Adapter. Features: 34-pin male and female connectors 8" length (210±10mm)
₹ 569.00 *
2.4GHz 6dBi Antenna with IPEX Connector for... Attention: It is ideal to use with a LattePanda V1.0 (NOT compatible with LattePanda Alpha/Delta). This is an omni-directional antenna with an IPEX connector. Its working frequency is 2.4GHz which meets most requirements of Wi-Fi...
₹ 489.00 *
myProto Protoboard for NI myDAQ & myRIO The Digilent myProto accessory board for the NI myDAQ and NI myRIO brings all your myDAQ/myRIO's signals to breadboard connections where they can be easily accessed using simple jumper wires, and even adds several useful I/O devices. The...
₹ 5,999.00 *
Shield Adapter (Uno R3) for NI myRIO With the Shield Adapter for NI myRIO , you can now connect your myRIO to the expansive shield options offered by the Arduino ecosystem. The Shield Adapter is designed to work with any shield that is compatible with the Arduino® Uno using...
₹ 2,499.00 *
Motor Adapter for NI myRIO The Motor Adapter for NI myRIO allows you to easily connect and control either one stepper motor, two DC motors, or two servos independently through the MXP connector on your myRIO. It has been designed so that no additional circuitry is...
₹ 7,999.00 *
5MP Night Vision Camera for Raspberry Pi... This 5MP Night Vision Camera for Raspberry Pi is compatible with every version of Raspberry Pi, and comes with infrared lighting. It has infrared night vision mode, and the focus ring can be adjusted according to the position of objects....
₹ 3,649.00 *
Camera for Raspberry Pi (Compatible with... The camera for Raspberry Pi can be used to take high-definition video, as well as stills photographs. It’s easy to use for beginners, but has plenty to offer advanced users if you’re looking to expand your knowledge. There are lots of...
₹ 2,469.00 *
Coax Power Cable Features: 2.1mm female power connector for use with Digilent power supplies Useful for any Digilent product that can accept power from an outside source
₹ 229.00 *
HDMI Cable (Type A to Type D Micro) Features: 40" in length Type A to Type D Micro HDMI cable
₹ 1,489.00 *
Temp Hum 9 ReSpeaker Core ST-LINK V2 mini Raspberry Pi RS485 click Ultrasound SiK Telemetry High Power SRK Basic Servo I2C Shield for Clicker 2 for BLE TX Click Soil oxygen Pmod CAN CAN Slider 2 Click 3G SARA click NVIDIA Jetson Flash 2 click Pimoroni pHAT Industrial Arty A7-100T Electret Buck 10 Click Active GPS 6DOF IMU 4 Opto 3 click WiFi Relay ODROID-H4 PLUS NVIDIA Jetson LED SMD RGB Ultraviolet UNI-DS V8 Ammonia NH3 Gas Solid State Pololu Simple Arduino Due - BNC Adapter MCP2518FD click RS232 485 422 Carbon Dioxide 5.65inch ACeP Hydrogen Ambient 3 Click Air quality Fermion MEMS Riverdi Display
Viewed